Showing results: 496 - 510 of 550 items found.
-
iXA -
Kaelus
The Kaelus iXA Series Passive Intermodulation (PIM) analyzer is a dual-port, battery powered PIM Test Analyzer. It supports multiple test scenarios such as testing at the top of the tower, the base of the tower, rooftop, in-building for DAS systems and external PIM Finding.No other PIM tester has ever been integrated to this level! The iXA includes a network of electronic switches to change from one-port to two-port measurement seamlessly. In addition, with integrated Range-to-Fault (RTF) on each port, the user can first troubleshoot the system for internal PIM. Then, without reconnection, the user can progress with the external PIM process, making the entire process much more efficient.With integrated RTF on each port, the user can collect four times more range-to-fault data than the standard 1-port PIM Finder solution. Thus, the user can easily locate and swiftly eliminate the strongest PIM source.
-
PCIe-9814 -
ADLINK Technology Inc.
The ADLINK PCIe-9814 is a PCI Express digitizer providing speedy, high quality data acquisition. Each of the four input channels supports up to 80MS/s sampling, with 12-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no inter channel phase delay. The extremely large on-board memory enables long recording times even at the highest sampling rates.Unlike parallel PCI buses, PCI Express slots utilize serial point-to-point connection. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9814, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card. The ADLINK PCIe-9814 x4 digitizer can be used in any standard PCI Express slot, x4, x8, or x16.
-
AE6920T -
Keysight Technologies
Unlike CAN, LIN, Automotive Ethernet demands rigorous compliance verification using test cases that cover transmitters (Tx), receivers (Rx), and harness/connector assemblies. To help you save time and effort, Keysight offers solutions that automate the testing and validation across Transmitter (Tx), Receiver (Rx), and the connections between Automotive Ethernet devices. Our engineers have invested thousands of hours in learning the standards and creating automated, repeatable compliance tests. These proven applications help you ensure proper test configuration and valid measurement results. Ultimately, you’ll have greater confidence that your device is compliant. Now available for data rates up to 10Gbps. The automotive Ethernet test solution AE6900T offers hardware and accessories to make sure you have all of the components you need to get up and running quickly.
-
783688-01 -
NI
The cDAQ‑9135 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom dual-core processing and 32 GB nonvolatile storage for data-logging and embedded monitoring in extreme environments. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9135 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input, and an integrated NI‑XNET port. You can combine the cDAQ‑9135 with up to eight C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
783687-01 -
NI
1.33 GHz Dual-Core Atom, 8-Slot, CompactDAQ Controller - The cDAQ‑9133 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom dual-core processing and 16 GB nonvolatile storage for data-logging and embedded monitoring. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9133 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input. You can combine the cDAQ‑9133 with up to eight C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
783686-01 -
NI
1.33 GHz Dual-Core Atom, 8-Slot, CompactDAQ Controller - The cDAQ‑9133 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom dual-core processing and 16 GB nonvolatile storage for data-logging and embedded monitoring. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9133 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input. You can combine the cDAQ‑9133 with up to eight C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Labtone Test Equipment Co., LTD
Labtone EV series of electrodynamic shaker vibration test System simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications.Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.Labtone EV series of electromagnetic vibration testing system is specially designed to meet the need for long time operation. Vertical and horizontal vibrations can be achieved by the installation of vibration resistant base. The standard platform is equipped with high efficiency airbag shock isolation device, so that the vibration transmitted to the building can be minimized. There is no need for additional foundation in most of the cases.A complete set of vibration testing system is composed of shaker, power amplifier and vibration measuring control system, in accordance with the relevant national and international standards (such as: MIL-STD, DIN, ISO, ASTM, IEC, ISTA, GB, GJB, JIS, BS, etc.) to provide technical support for establishing product quality inspection.
-
HBM-VT -
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
CCT-100 -
Cosam Industries
Automatic Custom Cable Tester. Instantly test up to 52 test points as soon as you connect your cable. OLED display with pass/fail indicating light and audible notification. Steel construction: 7.75″ x 3.50″ x 1.5″Capable: 52 Test points (Cables up to 26 wires) Detects Opens, Shorts, Miss-wires, Bad connections, and Diode polarity.Versatile: Many standard connector boards available as well as a build-your-own option for specialized connectors.Compact: 75” x 3.5” x 1.5” (197 mm x 89 mm x 38 mm)Rugged: Made from 18 gauge cold rolled steel. Will last for decades.Fast: Tests at speeds up to thirty times per second and starts without pressing a button.Intuitive: Easy to read status updates shown on the clear and bright OLED display along with simple Pass/Fail indication by both green/red LED and dual-tone audio buzzer.
-
M4K1553Px(S) -
Excalibur Systems, Inc.
The M4K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M4K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M4K1553PxS single function (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.
-
785832-01 -
NI
6 GHz, 1 GHz Bandwidth, RF PXI Vector Signal Transceiver - The PXIe-5841 is a vector signal transceiver (VST) with 1 GHz of instantaneous bandwidth. It combines vector signal generator, vector signal analyzer and high-speed serial interface capabilities with FPGA-based real-time signal processing and control. The PXIe-5841 features the flexibility of a software defined radio architecture with RF instrument class performance. This VST delivers the fast measurement speed and small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments. The PXIe-5841 is available with an optional high-performance local oscillator module for improved phase noise, measurement time, and EVM performance. You can use the VST to test a variety of cellular and wireless standards such as Wi-Fi 6 and 5G NR. In addition, you can expand the small, two slot 2U PXI Express form factor to support multiple input, multiple output (MIMO) configurations.
-
786982-01 -
NI
6 GHz, 1 GHz Bandwidth, RF PXI Vector Signal Transceiver - The PXIe-5841 is a vector signal transceiver (VST) with 1 GHz of instantaneous bandwidth. It combines vector signal generator, vector signal analyzer and high-speed serial interface capabilities with FPGA-based real-time signal processing and control. The PXIe-5841 features the flexibility of a software defined radio architecture with RF instrument class performance. This VST delivers the fast measurement speed and small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments. The PXIe-5841 is available with an optional high-performance local oscillator module for improved phase noise, measurement time, and EVM performance. You can use the VST to test a variety of cellular and wireless standards such as Wi-Fi 6 and 5G NR. In addition, you can expand the small, two slot 2U PXI Express form factor to support multiple input, multiple output (MIMO) configurations.
-
784238-01 -
NI
1.91 GHz Quad-Core Atom, 4-Slot, CompactDAQ Controller - The cDAQ‑9136 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom quad-core processing and 32 GB nonvolatile storage for data-logging and embedded monitoring. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9136 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input, and an integrated NI‑XNET port. You can combine the cDAQ‑9136 with up to four C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
783341-01 -
NI
1.33 GHz Dual-Core Atom, 4-Slot, Extended Temperature CompactDAQ Controller - The cDAQ‑9134 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom dual-core processing and 32 GB nonvolatile storage for data-logging and embedded monitoring in extreme environments. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9134 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input, and an integrated NI‑XNET port. You can combine the cDAQ‑9134 with up to four C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
